Skip to content

Mechanical Technology Grade 12 NSC November 2023 Memo (Eng)

MemorandumMechanical TechnologyGrade 12202327 pages

Grade 12 Mechanical Technology memorandum from the NSC November Exam 2023 (English), 27 pages. Read online or download the free PDF.

Free to read online, no sign-up needed

Loading document…

Loading document…

Document textSearch extracted text and jump to a page.
Downloaded from hlayiso.com NATIONAL SENIOR CERTIFICATE GRADE 12 MECHANICAL TECHNOLOGY: FITTING AND MACHINING NOVEMBER 2023 MARKING GUIDELINES MARKS: 200 These marking guidelines consist of 27 pages. Copyright reserved Please turn over
Downloaded from hlayiso.com Mechanical Technology: Fitting and Machining 2 DBE/November 2023 NSC – Marking Guideline QUESTION 1: MULTIPLE-CHOICE (GENERIC) 1.1 B (1) 1.2 A (1) 1.3 C (1) 1.4 C (1) 1.5 A (1) 1.6 B (1) [6] Copyright reserved Please turn over
Downloaded from hlayiso.com Mechanical Technology: Fitting and Machining 3 DBE/November 2023 NSC – Marking Guideline QUESTION 2: SAFETY (GENERIC) 2.1 Examination checks:  Severe bleeding   Internal bleeding   Head injuries   Neck injuries   Fractures   Vital signs   Physical abnormalities  (Any 2 x 1) (2) 2.2 Safety devices on the power-driven guillotine:  Finger protectors / Fixed guards / Blade guard   Rear view mirrors   Rear light curtains   Automatic sweep-away   Revolving warning lights   Two-hand / dual control device   Additional emergency buttons   Self-adjusting guards   Covered footswitch  (Any 2 x 1) (2) 2.3 Grinding wheel:  The wheel should be rated above the speed of the motor.   Check for cracks on the grinding wheel.   Check for chips on the grinding wheel.   Check that the arbor hole is the correct size.   Must not be contaminated by oil/fluids or grease.   Correct size of the wheel.   Correct type of wheel for the material.  (Any 2 x 1) (2) 2.4 Gas welding equipment – safety devices:  Valve guard   Flash back arrestor   Pressure regulator   C-clamps on hoses/Parallel hose clips   Acetylene spindle key must always be in place.   Cylinder valves.  (Any 2 x 1) (2) Copyright reserved Please turn over
Downloaded from hlayiso.com Mechanical Technology: Fitting and Machining 4 DBE/November 2023 NSC – Marking Guideline 2.5 Advantages of process layout of machines are:  High machine utilisation.   Better supervision.   Less interruption in the flow of work.   Lower equipment costs.   Better control of total manufacturing costs.   Greater flexibility.  (Any 2 x 1) (2) [10] Copyright reserved Please turn over
Downloaded from hlayiso.com Mechanical Technology: Fitting and Machining 5 DBE/November 2023 NSC – Marking Guideline QUESTION 3: MATERIALS (GENERIC) 3.1 Colour code of metal:  To identify the type of metal.   To identify carbon content especially after the metal was stored.   To identify the profile/size of the metal.  (Any 1 x 1) (1) 3.2 Tests to determine properties of steel: 3.2.1 Sound test:  Hardness   Softness  (Any 1 x 1) (1) 3.2.2 Bending test:  Ductility   Bend strength   Fracture strength   Resistance to fracture  Brittleness   Elasticity   Plasticity   Flexibility  (Any 1 x 1) (1) 3.2.3 Machining test:  Hardness   Strength  (Any 1 x 1) (1) 3.3 Reasons metal soaked during heat treatment:  To ensure uniform heat distribution  throughout the metal.   To achieve a uniform grain structure  after cooling the metal.  (Any 1 x 2) (2) 3.4 Case hardening:  Carburising   Nitriding   Cyaniding  (Any 2 x 1) (2) 3.5 Annealing process: Heating the steel slightly above AC3, (upper critical temperature)  soaking it for a required time/period  and then slow cooling  back to room temperature. (3) Copyright reserved Please turn over
Downloaded from hlayiso.com Mechanical Technology: Fitting and Machining 6 DBE/November 2023 NSC – Marking Guideline 3.6 Rapid quenching mediums:  Brine/Salt water   Water   Nitrogen   Oil  (Any 2 x 1) (2) 3.7 Heat treatment process: Tempering  (1) [14] Copyright reserved Please turn over
Downloaded from hlayiso.com Mechanical Technology: Fitting and Machining 7 DBE/November 2023 NSC – Marking Guideline QUESTION 4: MULTIPLE-CHOICE (SPECIFIC) 4.1 D (1) 4.2 A (1) 4.3 A (1) 4.4 C (1) 4.5 D (1) 4.6 B (1) 4.7 B (1) 4.8 A (1) 4.9 C (1) 4.10 D (1) 4.11 B (1) 4.12 A (1) 4.13 C (1) 4.14 D (1) [14] Copyright reserved Please turn over
Downloaded from hlayiso.com Mechanical Technology: Fitting and Machining 8 DBE/November 2023 NSC – Marking Guideline QUESTION 5: TERMINOLOGY (LATHE AND MILLING MACHINE) (SPECIFIC) 5.1 Disadvantages of compound slide method  Only short tapers can be cut.   It causes fatigue to the operator.   The automatic feed of the machine cannot be used.  (Any 2 x 1) (2) 5.2 Taper calculations: 5.2.1 Length of taper:  D-d Tan  2 2 l D-d 2 l    tan 2 78 - 55 2l   tan4° 23 2l  0,069926811 328,9153283 l  2 l  164,46 mm  (4) 5.2.2 Tailstock set-over: L D - d  Set - over  2l   284,46  78 - 55   2  164,46  = 19,89 mm  (4) Copyright reserved Please turn over
Downloaded from hlayiso.com Mechanical Technology: Fitting and Machining 9 DBE/November 2023 NSC – Marking Guideline 5.3 Key ways: 5.3.1 Width: D Width = 4 83 Width =  4 = 20,75 mm  (2) 5.3.2 Thickness: D Thickness  6 83  Thickness  6  13,83 mm  (2) 5.3.3 Length: Length  1,5  diameter of shaft  1,5  83   124,50 mm  (2) 5.4 Straddle milling: A. Side and face cutter / Milling cutters.  B. Arbor / Spacers / Spindle / Axle  (2) [18] Copyright reserved Please turn over
Downloaded from hlayiso.com Mechanical Technology: Fitting and Machining 10 DBE/November 2023 NSC – Marking Guideline QUESTION 6: TERMINOLOGY (INDEXING) (SPECIFIC) 6.1 Gear terminology: 6.1.1 Pitch-circle diameter: PCD  m  T CP  m    2,5  180   2,5    450 mm   7,85 mm  CP  T OR PCD   7,85 180    450mm  (2) 6.1.2 Dedendum: Dedendum  1,157  m Dedendum  1,25  m  1,157  2,5  OR  1,25  2,5   2,89 mm   3,13 mm  (2) 6.1.3 Outside diameter: OD  PCD  2m  450  22,5    455 mm  (2) Copyright reserved Please turn over
Downloaded from hlayiso.com Mechanical Technology: Fitting and Machining 11 DBE/November 2023 NSC – Marking Guideline 6.2 Dovetails: W = 136 + 2(DE) m = W – [2(AC) + 2(R)] OR m = W – 2(AC + R) OR m = W – 2(AC) – 2(R) 6.2.1 Maximum width distance of dove tail: (W) Calculate DE or y: AD tanθ = DE DE tan  AD 50 tan60° = DE  tan  AD  OR DE  tan30°  50  DE = 50  28,87 mm  tan60° = 28,87mm W  136  2(DE)   136  2(28,87)   136  57,74  193,74 mm  (6) Copyright reserved Please turn over
Downloaded from hlayiso.com Mechanical Technology: Fitting and Machining 12 DBE/November 2023 NSC – Marking Guideline 6.2.2 Distance between the rollers: (m) Calculate AC or x: BC Tan = AC AC Tan = BC BC AC =  AC =Tan  BC  Tan OR 10 =Tan60o  10  =  Tan30o =17,32mm  =17,32mm  m = W – [(2(AC) + 2(R)]  = 193,74 – [2(17,32) + 2(10)]  = 193,74 – (34,64 + 20) = 139,10 mm  OR m = W – 2(AC + R)  = 193,74 – 2(17,32 + 10)  = 193,74 – (34,64 + 20) = 139,10 mm  OR m = W – 2(AC) – 2(R)  = 193,74 – 2(17,32) – 2(10)  = 193,74 – 34,64 – 20 = 139,10 mm  (6) Copyright reserved Please turn over
Downloaded from hlayiso.com Mechanical Technology: Fitting and Machining 13 DBE/November 2023 NSC – Marking Guideline 6.3 Milling of spur gear: 6.3.1 Indexing: 40 40 Indexing   N 89 40 40    A 90 4 6   9 6 24   54   Indexing : 0 full turns and 24 holes on a 54  hole circle (3) 6.3.2 Change gears: Dr 40   A  n  Dn A Driver A -N 40   Dr 40 Driven A 1   90  89    Dn 90 90 - 89 40    90 1 40  1 90 1 40   90 1 40 OR  90  40   90 4  9 4 8    9 8 4 8    9 8 Dr 32   Dn 72  Dr 32   Dn 72  (5) Copyright reserved Please turn over
Downloaded from hlayiso.com Mechanical Technology: Fitting and Machining 14 DBE/November 2023 NSC – Marking Guideline 6.4 Balancing constraints/disadvantages:  Requires specialised machinery.   Difficult to ascertain the exact point of unbalance.   Requires accurate removal or adding of material (weight) to the object.   Can lead to interference with parts of the machine when weights are added to parts.  (Any 2 x 1) (2) [28] Copyright reserved Please turn over
Downloaded from hlayiso.com Mechanical Technology: Fitting and Machining 15 DBE/November 2023 NSC – Marking Guideline QUESTION 7: TOOLS AND EQUIPMENT (SPECIFIC) 7.1 Instrument to measure indentation: Microscope  (1) 7.2 Brinell hardness number:  Calculations   The use of a Brinell hardness table  (2) 7.3 Function of moment tester: To determine the reactions on either side of a simply loaded beam.  (1) 7.4 Principal of tensile tester: The tensile tester is a destructive  tester that subjects a piece of material to an increasing axial load  while measuring the corresponding elongation of the material. (3) 7.5 Depth and screw-thread micrometer: The scale on the depth micrometer’s barrel reads in the opposite direction compared to the screw thread micrometer.  (1) 7.6 Hardness assessment:  Resistance to penetration / Hardness tests   Sound test   Elastic hardness / Bending test / Tensile test   Resistance to abrasion / File test / Spark test / Machining test  (Any 3 x 1) (3) 7.7 Micrometer measurement:   5,94 + 50 = 55,94 mm (2) [13] Copyright reserved Please turn over
Downloaded from hlayiso.com Mechanical Technology: Fitting and Machining 16 DBE/November 2023 NSC – Marking Guideline QUESTION 8: FORCES (SPECIFIC) 8.1 Forces: 8.1.1 Horizontal component:  HC  45cos0  75cos30  15cos75 120cos270     HC  45  64,95  3,88  0  HC  106,07 N  (4) 8.1.2 Vertical component:  VC  45sin0  75sin30  15sin75  120sin270     VC  0  37,5  14,49  120  VC   68,01 N  (4) OR Force θ 8.1.1 ∑HC/x = Fcosθ 8.1.2 ∑VC/y = Fsinθ 45N 0º HC = 45cos0° 45N  VC = 45sin0° 0N 75N 30º HC = 75cos30° 64,95N  VC = 75sin30° 37,5N  15N 105º HC = 15cos105° -3,88N  VC = 15sin105° 14,49N  120N 270º HC = 120cos270° 0N VC = 120sin270° -120N  Total 106,07N  -68,01N  (8) 8.1.3 Resultant: R 2  VC2  HC2  68,01  106,07   2 2 R R  15876,21 R  126,00 N  (2) Copyright reserved Please turn over
Downloaded from hlayiso.com Mechanical Technology: Fitting and Machining 17 DBE/November 2023 NSC – Marking Guideline 8.1.4 Angle and direction of resultant: Angle: VC tanθ  HC  68,01   θE θ  tan1    106,07   θ  tan1  0,64  R S θ  32,67  Direction: R =126,00N 32,67° / 32°40' South of East  OR Angle: HC tan = VC E  106,07   θ  = tan-1   R  -68,01   S  = tan-1 1,559623585   = 57,20°  Direction: R =126,00N 57,33° / 57°20' East of South  (4) Copyright reserved Please turn over
Downloaded from hlayiso.com Mechanical Technology: Fitting and Machining 18 DBE/November 2023 NSC – Marking Guideline 8.2 Reaction in supports A and B: Reaction in support A: Take moments about B:  LHM   RHM     55  7      A  7  160  1,5  385  7A  240 145 A  7 A  20,71 N  Reaction in support B: Take moments about A:  LHM   RHM   B  7    55  0   160  8,5  7B  0  1360 1360 B  7 B  194,29 N  (9) Copyright reserved Please turn over
Downloaded from hlayiso.com Mechanical Technology: Fitting and Machining 19 DBE/November 2023 NSC – Marking Guideline 8.3 Stress and strain: 8.3.1 Maximum load: π D2 A 4 π 0,022   4  3,14159265  10 -4 m2  OR 3,14  10 -4 m2  F σ A F  Aσ    F = 3,14159265×10-4  640  106 F = 201061,93 N F = 201,06 kN  OR 200,96kN  (6) 8.3.2 Safe working stress: MS SF  SS MS SS   SF 640  106  SS  3  SS  213333333,3 Pa SS  213,33 MPa  (4) [33] Copyright reserved Please turn over
Downloaded from hlayiso.com Mechanical Technology: Fitting and Machining 20 DBE/November 2023 NSC – Marking Guideline QUESTION 9: MAINTENANCE (SPECIFIC) 9.1 Preventative maintenance: Subgroups of preventative maintenance:  Planned or scheduled maintenance   Conditional-based maintenance  (2) 9.2 Advantages of belt drives over gear drives:  Produce less noise than gear drives.   Produce less vibration than gear drives.   More cost effective.  Belt drives will slip under a sudden load /over load to protect the drive.   Do not need lubrication like gear drives.  Belt drives do not require parallel shafts.   Belts can be used over long distances.  (Any 3 x 1) (3) 9.3 Belt drives:  V-pulley   Wedge pulley   Flat pulley   Round belt   Timing/Toothed belt   Multi-groove belt  (Any 3 x 1) (3) 9.4 Non-stick material: Teflon  (1) 9.5 Uses: Polyvinyl chloride (PVC): 9.5.1  Trays for food and toiletries   Clear bottles   Blister packaging   Drain and sewerage pipes   Electrical pipes   Drip bags   Cooking bottles   Vinegar bottles   Credit cards   Shoe soles   Floor tiles   Wallpaper   Outdoor furniture   Disposable cutlery  (Any 2 x 1) (2) Copyright reserved Please turn over
Downloaded from hlayiso.com Mechanical Technology: Fitting and Machining 21 DBE/November 2023 NSC – Marking Guideline 9.5.2 Bakelite:  Electrical insulators   Kitchenware   Jewellery   Toys   Distributor rotors   Disc brake cylinders   Sauce pan handles   Electrical switches   Electrical parts   Aircraft components   Bearings   Clutch linings   Brake linings   Laminated materials   Computer motherboards  (Any 2 x 1) (2) 9.5.3 Fibre Glass  Surface covering   Woven cloth   Pillow stuffing   Reinforced plastics   Boats   Motor vehicle bodies   Roof sheeting   Petrol tanks   Swimming pools   Furniture   Fruit and salad bowls   Ornaments   Sporting equipment   Jigs forms  (Any 2 x 1) (2) 9.6 Thermo-hardened or thermoplastic: 9.6.1 Carbon fibre: Thermo-hardened / Thermosetting  (1) 9.6.2 Nylon: Thermoplastic  (1) 9.6.3 Bakelite: Thermo-hardened / Thermosetting  (1) [18] Copyright reserved Please turn over
Downloaded from hlayiso.com Mechanical Technology: Fitting and Machining 22 DBE/November 2023 NSC – Marking Guideline QUESTION 10: JOINING METHODS (SPECIFIC) 10. 1 Square screw thread: Crest  Root   (For the sketch) (3) 10.2 Square Thread: 10.2.1 Pitch diameter: Lead Pitch  Number of starts 25   2  12,50 mm  P PD  OD - 2 12,50  70 -  2 PD  63,75 mm  (4) 10.2.2 Helix angle of the thread: Lead Tan    Dp 25  Tan    63,75    tan-1  0,124827406   = 7,12 OR 7 7'  (4) 10.2.3 Leading angle: Leading angle (Helix angle + Clearance angle) (7,12° + 3°)  = 79,88° OR 7 53’  (2) Copyright reserved Please turn over
Downloaded from hlayiso.com Mechanical Technology: Fitting and Machining 23 DBE/November 2023 NSC – Marking Guideline 10.2.4 Following angle: Following angle = 90° + (Helix angle – Clearance angle) = 90° + (7,12 3°)  = 94,12° OR 94°7’  (2) 10.3 ISO V-screw thread: A. Helix angle  B. Pitch / Lead  C. Root  (3) [18] Copyright reserved Please turn over
Downloaded from hlayiso.com Mechanical Technology: Fitting and Machining 24 DBE/November 2023 NSC – Marking Guideline QUESTION 11: SYSTEMS AND CONTROL (DRIVE SYSTEMS) (SPECIFIC) 11.1 Hydraulic systems : 11.1.1 Area of Ram:  D2 A Ram   4  (0,110) 2 A  4 A  0,0095 m 2  OR 9,50×10 -3 m 2  (2) 11.1.2 Applied force on plunger: F p A f F   a A Fa f A 350  0,005 f  0,0095 f  184,21 N  (3) Copyright reserved Please turn over
Downloaded from hlayiso.com Mechanical Technology: Fitting and Machining 25 DBE/November 2023 NSC – Marking Guideline 11.1.3 Displacement h: VPlunger = VRam a × h  A ×H A ×H  h a 0,0095  0,025 h  0,005 h  0,0475 m h  47,5 mm  (3) 11.2 Pressure gauge:  To adjust pressure control valves.   Determining the pressure being exerted.   For safety.   Indicates if leakages are present in the system.  (Any 2 x 1) (2) 11.3 Advantages of pneumatics:  Pneumatic tools are very environmentally friendly. / Clean operation   Last longer.   More robust.   More compact.   Easily maintained.   Easily installed.  Cost effective.   Safe to use.   High power-to-weight ratio.   Simple control.   Quick response.   Versatile.  (Any 1 x 1) (1) Copyright reserved Please turn over
Downloaded from hlayiso.com Mechanical Technology: Fitting and Machining 26 DBE/November 2023 NSC – Marking Guideline 11.4 Belt drive: 11.4.1 The rotational frequency in r/sec: N DR  D DR  N DN  D DN N DR  D DR N DN   D DN 25  75  N DN  350  N DN  5,36 r / sec  (4) 11.4.2 Belt speed: Belt Speed  V   π DDR  NDR Belt Speed  V   π DDR  NDR  π  0,075  25  OR  π  0,350  5,36   5,89 m / s   5,89 m / s  (2) 11.5 V-Belt: The slippage of the v-belt.  (1) 11.6 Gear drives: 11.6.1 The rotational frequency: N input Product of teeth on driven gears  N output Product of teeth on driver gears NA TB  TD  ND TA  TC 95 55  50   ND 30  25  30  25  95 ND   55  50 71250 ND  2750 N D  25,91 r / min  (4) Copyright reserved Please turn over
Downloaded from hlayiso.com Mechanical Technology: Fitting and Machining 27 DBE/November 2023 NSC – Marking Guideline 11.6.2 Power transmitted: 2 N T Power P   60 2 ×  × 95 ×120  P 60 P  1193,81  Watt(W )  OR P  1,19  Kilowatt(kW )  (3) 11.7 Length of spanner: Torque(T )  Force Radius  T Radius   F 135 Radius   300 Radius  0,45 m  OR Radius  450 mm  (3) [28] TOTAL: 200 Copyright reserved

Study this subject

More from Grade 12 Mechanical Technology

View all