Downloaded from hlayiso.com
SENIOR CERTIFICATE EXAMINATIONS/
NATIONAL SENIOR CERTIFICATE EXAMINATIONS
CIVIL TECHNOLOGY: CIVIL SERVICES
2021
MARKS: 200
TIME: 3 hours
This question paper consists of 16 pages and 4 answer sheets.
Copyright reserved Please turn over
Skip to contentAll 2021 papers %20Eng_hlayiso.com_--f39d7571-db9f-4ded-b5e7-27008235ca8b/v1-4efe03b2e24afe8e530e/card.webp)


%20Eng_hlayiso.com_--8f870317-4f98-4448-b660-0d528b30c2a4/v1-c304a8b770601b9842d8/card.webp)
%20Afr_hlayiso.com_--ff7a7835-2450-4747-baaf-85c46ef7d411/v1-8ec16443e4393e6a6260/card.webp)
%20Eng_hlayiso.com_--e6743728-8140-42ae-838d-282654a975a5/v1-dce3e047e0d7ad60a32b/card.webp)
View all%20(Afrikaans)%20June%202025%20Possible%20Answers--c0a65d19-28ca-4ac3-8c61-d4627d2a3133/v1-5f42c573694769cf80ce/card.webp)
%20MG%20Eng--0e265899-dc44-4809-aabf-8f374f1af392/v1-73a07814cfc9334618a1/card.webp)




Civil Technology Grade 12 NSC November 2021 QP (Eng)
Grade 12 Civil Technology question paper from the NSC November Exam 2021 (English), 21 pages. Read online or download the free PDF.
Civil Technology · Grade 12 · NSC November Exam · 2021. Question paper, 21 pages. Read online or download the PDF.
- Subject
- Civil Technology
- Grade
- Grade 12
- Document type
- Question paper
- Year
- 2021
- Exam period
- NSC November Exam
- Curriculum
- CAPS
- Pages
- 21
- File size
- 490.6 KB
Free to read online, no sign-up needed
Loading document…
Loading document…
1 of 21
This exam
Document textSearch extracted text and jump to a page.
Downloaded from hlayiso.com
Civil Technology: Civil Services 2 DBE/2021
SC/NSC
REQUIREMENTS:
1. Drawing instruments
2. A non-programmable calculator
3. ANSWER BOOK
INSTRUCTIONS AND INFORMATION
1. This question paper consists of SIX questions.
2. Answer ALL the questions.
3. Read all the questions carefully.
4. Answer each question as a whole. Do NOT separate subsections of
questions.
5. Number the answers correctly according to the numbering system used in this
question paper.
6. Start the answer to EACH question on a NEW page.
7. Do NOT write in the margins of the ANSWER BOOK.
8. You may use sketches to illustrate your answers.
9. Write ALL calculations and answers in the ANSWER BOOK or on the
attached ANSWER SHEETS. The SI unit for answers must be indicated next
to the answer.
10. Use the mark allocation as a guide to the length of your answers.
11. Make drawings and sketches in pencil, fully dimensioned and neatly finished
off with descriptive titles and notes to conform to the SANS/SABS Code of
Practice for Building Drawings.
12. For the purpose of this question paper, the size of a brick should be taken as
220 mm x 110 mm x 75 mm.
13. Use your own discretion where dimensions and/or details have been omitted.
14. Answer QUESTIONS 2, 3.10, 5.4 and 6.10 on the attached ANSWER
SHEETS using drawing instruments, where necessary.
15. Write your CENTRE NUMBER and EXAMINATION NUMBER on every
ANSWER SHEET and hand them in with your ANSWER BOOK, whether you
have used them or not.
16. Drawings in the question paper are NOT to scale due to electronic transfer.
17. Google Images were used as the source of all photographs and pictures.
18. Write neatly and legibly.
Copyright reserved Please turn over
Downloaded from hlayiso.com
Civil Technology: Civil Services 3 DBE/2021
SC/NSC
QUESTION 1: OHSA, SAFETY, MATERIALS, TOOLS, EQUIPMENT AND
JOINING (GENERIC)
Start this question on a NEW page
1.1 Give ONE word/term for each of the following descriptions by choosing a
word/term from the list below. Write only the word/term next to the question
numbers (1.1.1. to 1.1.5) in the ANSWER BOOK, e.g. 1.1.6 casement
curing; electroplating; galvanising; powder coating;
paint; turpentine; sanding sealer
1.1.1 Available in a water- or oil-based liquid (1)
1.1.2 Allows concrete to achieve its optimal strength (1)
1.1.3 Coating a metal by the process of electrolysis (1)
1.1.4 Can be melted again because no chemical process is involved (1)
1.1.5 Adds strength to the original uncoated metal (1)
1.2 FIGURE 1.2 below shows equipment that is used on a construction site.
A B
FIGURE 1.2
1.2.1 State TWO materials that the equipment can be manufactured of. (2)
1.2.2 Deduce from FIGURE 1.2 the safest option to use, A or B.
Motivate your answer. (2)
Copyright reserved Please turn over
Downloaded from hlayiso.com
Civil Technology: Civil Services 4 DBE/2021
SC/NSC
1.2.3 Explain the purpose of the equipment in FIGURE 1.2. (1)
1.2.4 How far from a wall should the base of a ladder be placed to
ensure that it is positioned safely? (1)
1.3 A laser level is often used in construction.
1.3.1 Explain what you will determine if you use the laser level in EACH
of the following cases:
(a) When installing a sewerage system for a building (1)
(b) When laying tiles against a wall (1)
1.3.2 Explain what will happen if the tripod is not wide enough when
setting up the laser level. (1)
1.4 Explain what will happen if a worker manually lifts excessively heavy loads. (1)
1.5 The use of scaffolds is not permitted, unless inspected.
1.5.1 When should scaffolding be inspected? (1)
1.5.2 Who is responsible for the inspection of the scaffolding? (1)
1.6 FIGURE 1.6 below shows a joining fixture that can be used on building sites.
FIGURE 1.6
1.6.1 Identify the joining fixture. (1)
1.6.2 Name the part that should be used with the joining fixture. (1)
1.6.3 Explain why it is a better option to use this joining fixture to join two
steel sections. (1)
[20]
QUESTION 2: GRAPHICS AS MEANS OF COMMUNICATION (GENERIC)
Start this question on a NEW page.
FIGURE 2 on the next page shows a drawing that appears on a building plan. Analyse
the drawing and complete the table on ANSWER SHEET 2.
Copyright reserved Please turn over
Downloaded from hlayiso.com
Civil Technology: Civil Services 5 DBE/2021
SC/NSC
NOTES:
Contractors must verify all
dimensions and levels on site before
PLOT 53 commencing work. Architects are to
be notified of any discrepancies
25 000 immediately.
ARCHITECT'S SIGNATURE ………………….
14 100 CLIENT'S SIGNATURE ……………………….
1
10 000
3 000 4 000 10 000 3 000 The following symbol must be
indicated on a floor plan:
2 One-way switch – double-pole
3 000
The following item must be installed
3 in the bathroom:
4 000
4
PLOT 49 10
35 000 NEW
DWELLING
12 000 20 000
5
Main sewer line to be installed at a
slope of 1 : 40.
Brick force to be installed every
third course up to window height and
4 000
PLOT 51
on every course from the top of the
window up to wall plate level.
3 000 Pavement of 1,5 m wide must be
5 000 paved.
6
PAVEMENT 1 500 WIDE 1 30/05/2021 RECTIFY
DIMENSION
7
REVISION DATE DESCRIPTION
PROTEA STREET PRINTED BY: DATE OF PRINT:
HENSON PRINTERS 01/04/2021
8
DRAWING TITLE:
SITE PLAN PLOT 51
PAVEMENT
PROJECT:
PROPOSED NEW DWELLING ON PLOT 51,
DEEP RIVER
PROJECT NO. DRAWING NO.
GR 448-209 559P9
DATE DRAWN CHECKED SCALE
16/04/2021 JP NSIKI P GUNTER 1 : 200
REFERENCE CODE
SCALE 1 : 200 9 QP 2–2021
FIGURE 2 [40]
Copyright reserved Please turn over
Downloaded from hlayiso.com
Civil Technology: Civil Services 6 DBE/2021
SC/NSC
QUESTION 3: CONSTRUCTION ASSOCIATED WITH CIVIL SERVICES, OHSA
AND QUANTITIES (SPECIFIC)
Start this question on a NEW page.
3.1 FIGURE 3.1 below is a drawing of a temporary excavation exposing the
existing foundations. Study the drawing and answer the questions that follow.
B
A
≥300 mm
1
≥2
FIGURE 3.1
3.1.1 What does A indicate on this drawing? (1)
3.1.2 Identify B. (1)
3.1.3 Excavations always cause some ground movement. Name any
TWO factors that can cause ground movement. (2)
3.1.4 Deduce the slope of the excavation from the drawing. (2)
3.2 Name the TWO acceptable colours for the warning signals that should be
visible around excavations. (2)
3.3 Name TWO items that should NOT be placed near the edge of an excavation. (2)
3.4 Describe briefly the process of soil compaction. (2)
3.5 Name ONE type of soil that will be suitable for the use of jetting as a
compaction method. (1)
Copyright reserved Please turn over
Downloaded from hlayiso.com
Civil Technology: Civil Services 7 DBE/2021
SC/NSC
3.6 FIGURE 3.6 below is a picture of a construction that is used to protect
workers when working in excavations. Study FIGURE 3.6 and answer the
questions that follow.
FIGURE 3.6
3.6.1 Identify the construction in FIGURE 3.6. (1)
3.6.2 Explain the purpose of the sides of the construction. (1)
3.7 FIGURE 3.7 below is a drawing of a cylindrical water tank. Study the drawing
and calculate the volume of the tank in m³ in your ANSWER BOOK. Show
ALL formulae and calculations. Round off your answer to TWO decimal
places.
Ø 1 600
3 100
FIGURE 3.7 (6)
3.8 State the formula that you will use to calculate the volume of a cubical water
tank. (1)
3.9 Give the amount of water in litres that you would need to fill a tank of 1 m³. (1)
3.10 ANSWER SHEET 3.10 shows the first plan course of a half-brick wall with a
double return angle and an incomplete second plan course built in stretcher
bond. Use the information given in the first plan course and project and draw
the second (alternate) plan course of the half brick wall. (7)
[30]
Copyright reserved Please turn over
Downloaded from hlayiso.com
Civil Technology: Civil Services 8 DBE/2021
SC/NSC
QUESTION 4: HOT- AND COLD-WATER SUPPLY, TOOLS, EQUIPMENT AND
MATERIALS (SPECIFIC)
Start this question on a NEW page.
4.1 FIGURE 4.1 below is a drawing of a device used in cold-water systems.
Study FIGURE 4.1 and answer the questions that follow.
A
B
C
D
FIGURE 4.1
4.1.1 Name the device in FIGURE 4.1. (1)
4.1.2 Identify parts A, B and C. (3)
4.1.3 Explain the function of D in this device. (1)
4.1.4 What will happen to part D if part A is turned anticlockwise? (1)
4.2 Differentiate between a pillar tap and a bibcock by referring to the way in
which it is installed to/onto a sanitary fitment. (2)
Copyright reserved Please turn over
Downloaded from hlayiso.com
Civil Technology: Civil Services 9 DBE/2021
SC/NSC
4.3 Choose a description from COLUMN B that matches an item in COLUMN A.
Write only the letter (A–L) next to the question numbers (4.3.1 to 4.3.8) in the
ANSWER BOOK, e.g. 4.3.9 M.
COLUMN A COLUMN B
4.3.1 Drain-cleaning rods A uses high-pressure water
4.3.2 Pipe-thread cutting machine B to test for leakages in drainage
systems
4.3.3 Centrifugal pump
C used to test the pressure of
4.3.4 Drain-cleaning machine liquids in plumbing systems
(Jetting machine)
D plate glass cover
4.3.5 Compressed-air test
apparatus E to convert kinetic energy into
hydrodynamic energy
4.3.6 Water-pressure testing
pump F attached to a plunger or coil
4.3.7 Reason why drain-cleaning G do not wear gloves while
rods are cleaned after use operating
4.3.8 A device with a manometer H to get rid of harmful bacteria
I to control waterflow
J control valve of water meter
K to ensure that it is clean and
shiny before it is stored
L cuts flat metal surfaces
(8 x 1) (8)
4.4 Identify the tool to be used in the following scenarios:
4.4.1 Determining differences between levels and vertical heights,
especially over longer distances (1)
4.4.2 Moving sludge or liquid containing suspended matter (1)
4.4.3 Ensuring a proper free-flowing sewer operation (1)
4.5 The water closet is one of the household fitments that uses a lot of water.
Explain ONE method that can be used to limit the water usage of the water
closet by using an ordinary object. (2)
4.6 Name the device that regulates the water level inside a cistern. (1)
Copyright reserved Please turn over
Downloaded from hlayiso.com
Civil Technology: Civil Services 10 DBE/2021
SC/NSC
4.7 FIGURE 4.7 below shows a drawing of a high-pressure geyser installation.
Study the drawing and answer the questions that follow.
A
B C
D
E
FIGURE 4.7
4.7.1 Explain the function of A. (1)
4.7.2 A very important device that regulates the incoming water pressure
was omitted at B. Name this device. (1)
4.7.3 Identify C. (1)
4.7.4 Is the water in pipe D HOT or COLD? Motivate your answer. (2)
4.7.5 Identify E. (1)
4.8 Draw the SANS approved symbols for the following hot-water systems:
4.8.1 Balancing device (2)
4.8.2 Pressure-control valve (2)
4.8.3 Pressure switch (2)
4.9 Many faults can occur in hot-water systems.
4.9.1 Predict what could be the cause if water splutters through the taps. (1)
4.9.2 Explain how this fault can be prevented. (1)
4.10 State TWO precautionary methods to avoid an electrolytic reaction in a water
system. (2)
Copyright reserved Please turn over
Downloaded from hlayiso.com
Civil Technology: Civil Services 11 DBE/2021
SC/NSC
4.11 Galvanised sheeting is covered with a thin coating of oil to avoid white rust
between the sheets while stored. These sheets must be cleaned before they
can be soldered.
4.11.1 Name ONE type of acid that can be used to remove the galvanised
layer on these sheets before soldering. (1)
4.11.2 Give the scientific name of the white rust/corrosion that can occur
when zinc is dissolved and removed from an alloy. (1)
[40]
Copyright reserved Please turn over
Downloaded from hlayiso.com
Civil Technology: Civil Services 12 DBE/2021
SC/NSC
QUESTION 5: GRAPHICS AS MEANS OF COMMUNICATION, ROOF WORK AND
STORM WATER (SPECIFIC)
Start this question on a NEW page.
5.1 Draw a neat freehand drawing in your ANSWER BOOK to show the
installation of a gutter, down-pipe installation with an offset pipe and rain-
water shoe as seen from the side. (6)
5.2 FIGURE 5.2 below shows drawings of a concrete shoe and a surface
channel. Explain the purpose of each.
CONCRETE SHOE SURFACE CHANNEL
FIGURE 5.2 (2)
5.3 Flashing is used for waterproofing roofs. Name TWO materials that are used
for flashing. (2)
5.4 ANSWER SHEET 5.4 shows the front view and top view of a cylindrical pipe
elbow.
Use the drawing and the information on ANSWER SHEET 5.4 and draw ONE
development of the vertical cylindrical pipe elbow. Start the development at A,
showing the 3 mm seam on both sides.
Show ALL construction lines. Do NOT redraw the given views. Project the
development from the given views. (20)
[30]
Copyright reserved Please turn over
Downloaded from hlayiso.com
Civil Technology: Civil Services 13 DBE/2021
SC/NSC
QUESTION 6: SEWERAGE, SANITARY FITTINGS AND JOINING (SPECIFIC)
Start this question on a new page.
6.1 Various options are given as possible answers to the following questions.
Choose the answer and write only the letter (A–D) next to the question
numbers (6.1.1 to 6.1.5) in the ANSWER BOOK, e.g. 6.1.6 C.
6.1.1 … can be used to secure copper pipes to different surfaces.
A Perforated straps
B Plastic plumbing tape
C PVC weld, 50 mm
D None of the above-mentioned (1)
6.1.2 When using a pipe cutter to cut pipes, you must do the following:
A Place the pipe in a pipe vice or hold it firmly in one hand.
B Rotate the tool clockwise or anticlockwise to ensure that the
wheel cuts into the metal.
C Tighten the pipe cutter a little and turn again until the pipe is
cut.
D All the above-mentioned (1)
6.1.3 The ratio of the metals used in lead-free solder will depend on the
… during the soldering process.
A temperature
B type of metal to be soldered
C length of the joint
D soldering iron used (1)
6.1.4 The following is a type of flux that can be used when soldering.
A Tin flux
B Zinc acid
C Zinc chloride
D Hydro chloride (1)
6.1.5 To make and complete a grooved seam joint, you will use a mallet
and …
A a cold chisel.
B a soldering iron.
C grooving tool.
D None of the above-mentioned (1)
Copyright reserved Please turn over
Downloaded from hlayiso.com
Civil Technology: Civil Services 14 DBE/2021
SC/NSC
6.2 FIGURE 6.2 below shows a method used to join two or more materials
together. Study the drawing and answer the questions that follows.
A
FIGURE 6.2
6.2.1 Identify the tool illustrated in FIGURE 6.2. (1)
6.2.2 Name ONE material that is normally used to manufacture the nail
of A. (1)
6.2.3 Name ONE material that is used for the manufacturing of the head
of A. (1)
Copyright reserved Please turn over
Downloaded from hlayiso.com
Civil Technology: Civil Services 15 DBE/2021
SC/NSC
6.3 FIGURE 6.3 below shows a sectional view of a sink with the required pipe
work and a gully. Study the drawing and answer the questions that follow.
A
D
B
C
FIGURE 6.3
6.3.1 Identify parts A–D. (4)
6.3.2 Describe the purpose of part C. (1)
6.3.3 Name TWO types of gully traps. (2)
6.3.4 Describe the purpose of the water that stays behind inside the gully
trap. (1)
6.3.5 Explain ONE disadvantage of a gully. (1)
6.4 Explain the function of an overflow outlet on sanitary fitments. (2)
Copyright reserved Please turn over
Downloaded from hlayiso.com
Civil Technology: Civil Services 16 DBE/2021
SC/NSC
6.5 Name TWO sanitary fitments that can be manufactured with waste overflows. (2)
6.6 Compare a rodding eye and a stop end with regard to their uses. (2)
6.7 State ONE characteristic of EACH of the following materials used for sanitary
fitments:
6.7.1 Ceramics (1)
6.7.2 Terrazzo (1)
6.8 Draw the symbol for a rainwater shoe. (2)
6.9 FIGURE 6.9 below shows a sectional view of a septic tank. Study the drawing
and explain the working process of a septic tank.
FIGURE 6.9 (6)
6.10 ANSWER SHEET 6.10 shows part of an incomplete horizontal sectional view
of a manhole with a junction. Use ANSWER SHEET 6.10 and draw the
complete horizontal sectional view. Indicate the direction of flow of the
sewage by means of an arrow. (7)
[40]
TOTAL: 200
Copyright reserved
Downloaded from hlayiso.com
Civil Technology: Civil Services DBE/2021
SC/NSC
CENTRE NUMBER:
EXAMINATION NUMBER:
ANSWER SHEET 2
NO. QUESTION ANSWER MARKS
1. Identify the type of plan in FIGURE 2. 1
Deduce from the notes the brick force
2. 1
installation up to window height.
Deduce the scale that is used for
3. 1
FIGURE 2.
4. Identify number 1. 1
5. Identify number 3. 1
6. Identify number 5. 1
7. Identify number 7. 1
8. Identify number 8. 1
9. Identify number 9. 1
Name the item in the column for the
10. notes in FIGURE 2 that must be 1
installed in the bathroom.
Draw the electrical symbol as
11. described in the column for the notes 2
in FIGURE 2
Deduce from FIGURE 2 which
12. 1
company printed the building plan.
13. Give the abbreviation for number 2. 1
State the colour that you would use to
14. indicate the new dwelling on the site 1
plan.
Deduce from FIGURE 2 why the new
15. 1
dwelling is to be built on a corner plot.
Deduce the plot number of the new
16. 1
dwelling illustrated in FIGURE 2.
Which elevation is the closest to
17. 1
Protea Street?
Copyright reserved
Downloaded from hlayiso.com
Civil Technology: Civil Services DBE/2021
SC/NSC
What is the plot number of the property
18. 1
on the western side of the dwelling?
19. Give the abbreviation for number 6. 1
State the slope at which the main 1
20.
sewer line should be installed.
21. Describe what was done as revision 1. 1
22. Deduce the dimension fault on the total
1
width of the dwelling.
23. State the project number for this plan. 1
24. What is the width of the pavement? 1
25. How many branch pipes are indicated
1
on the plan?
26. Explain the purpose of number 4. 1
In what SI unit are the dimensions
27. indicated on the plan? 1
Draw a neat freehand drawing of the
top view of the symbol of a single
28. kitchen sink, as indicated in the 3
SANS/SABS Code of Practice for
Building Drawings.
Recommend TWO types of building
29. materials that can be used to finish the 2
area at number 7.
Calculate the total area of the plot.
30. Give your answer in m². 3
Show ALL calculations.
Calculate the distance between
Number 1 and Number 3 on the north
31. 4
elevation.
Show ALL calculations.
TOTAL: 40
Copyright reserved
Downloaded from hlayiso.com
Civil Technology: Civil Services DBE/2021
SC/NSC
CENTRE NUMBER:
EXAMINATION NUMBER:
ANSWER SHEET 3.10
FIGURE 3.10
ASSESSMENT CRITERIA MARK CANDIDATE'S
MARK
Correctness of second plan course 7
TOTAL: 7
Copyright reserved
Downloaded from hlayiso.com
Civil Technology: Civil Services DBE/2021
SC/NSC
CENTRE NUMBER:
EXAMINATION NUMBER:
ANSWER SHEET 5.4
A
NO. ASSESSMENT CRITERIA MARK CANDIDATE'S
MARK
1 Correctness of development 20
TOTAL: 20
Copyright reserved
Downloaded from hlayiso.com
Civil Technology: Civil Services DBE/2021
SC/NSC
CENTRE NUMBER:
EXAMINATION NUMBER:
ANSWER SHEET 6.10
FIGURE 6.10
NO. ASSESSMENT CRITERIA MARK CANDIDATE'S
MARK
1 Correctness of drawing 6
2 Direction of flow 1
TOTAL: 7
Copyright reserved
Study this subject
Recommended for this subject
%20Eng_hlayiso.com_--f39d7571-db9f-4ded-b5e7-27008235ca8b/v1-4efe03b2e24afe8e530e/card.webp)
Question paper
Civil Technology Grade 12 NSC November 2021 QP (Eng)

Question paper
Civil Technology Grade 12 Eastern Cape Mock 2021 QP (Afr)

Question paper
Civil Technology Grade 12 Eastern Cape Mock 2021 QP (Eng)
%20Eng_hlayiso.com_--8f870317-4f98-4448-b660-0d528b30c2a4/v1-c304a8b770601b9842d8/card.webp)
Question paper
Civil Technology Grade 12 NSC June 2021 Question Paper (Eng)
%20Afr_hlayiso.com_--ff7a7835-2450-4747-baaf-85c46ef7d411/v1-8ec16443e4393e6a6260/card.webp)
Question paper
Civil Technology Grade 12 NSC June 2021 Question Paper (Afr)
%20Eng_hlayiso.com_--e6743728-8140-42ae-838d-282654a975a5/v1-dce3e047e0d7ad60a32b/card.webp)
Question paper
Civil Technology Grade 12 NSC November 2023 QP (Eng)
More from Grade 12 Civil Technology
%20(Afrikaans)%20June%202025%20Possible%20Answers--c0a65d19-28ca-4ac3-8c61-d4627d2a3133/v1-5f42c573694769cf80ce/card.webp)
Memorandum
Civil Technology Grade 12 Gauteng June 2025 Memo (Afrikaans)
%20MG%20Eng--0e265899-dc44-4809-aabf-8f374f1af392/v1-73a07814cfc9334618a1/card.webp)
Memorandum
Civil Technology Grade 12 NSC November 2025 Memo (English)

Memorandum
Civil Technology Grade 12 Eastern Cape Prelim 2024 Memo

Memorandum
Civil Technology Grade 12 Eastern Cape Prelim 2024 Memo

Memorandum
Civil Technology Grade 12 Eastern Cape Prelim 2024 Memo

Memorandum