Skip to content

Civil Technology Grade 12 NSC November 2018 Memo (English)

MemorandumCivil TechnologyGrade 12201819 pages

Grade 12 Civil Technology memorandum from the NSC November Exam 2018 (English), 19 pages. Read online or download the free PDF.

Free to read online, no sign-up needed

Loading document…

Loading document…

Document textSearch extracted text and jump to a page.
Downloaded from hlayiso.com GRAAD 12 NATIONAL SENIOR CERTIFICATE GRADE 12 CIVIL TECHNOLOGY: WOODWORKING NOVEMBER 2018 MARKING GUIDELINES MARKS: 200 These marking guidelines consist of 19 pages. Copyright reserved Please turn over
Downloaded from hlayiso.com Civil Technology: Woodworking 2 DBE/November 2018 NSC – Marking Guidelines QUESTION 1: OHSA, MATERIALS, TOOLS, EQUIPMENT AND JOINING (GENERIC) 1.1 1.1.1 F (1) 1.1.2 A (1) 1.1.3 G (1) 1.1.4 E (1) 1.1.5 B (1) 1.2 • Do not throw any tools or materials from a scaffold.  • Never jump on to and off a scaffold.  • Never overload a scaffold. • Remove or cover sharp edges or corners. • Always attach free-standing scaffoldings to a building. • Use a ladder to get on and off a scaffold. • Keep free of waste or any other obstruction. • Never jump on a scaffold while working on it. • Responsible/qualified person must ensure that scaffolding is safe, rigid, stable and firm or has no defects. • Scaffold must be supplied with guard rails/toe boards. • Scaffolds must be levelled on uneven ground. • Do not work on a scaffold in bad weather. • Wear a safety harness when working on scaffolding. • Do not throw tools on/off a scaffold. ANY TWO OF THE ABOVE (2) 1.3 • It prevents workers from falling off the scaffold.  • It is used as a handrail.  • It is used to strap on safety harnesses. • To protect the worker working on the scaffold. ANY TWO OF THE ABOVE (2) 1.4 • The primary purpose of painting is to protect metals, wood and other material against corrosion and decay.  • Provides a decorative/aesthetic appearance/finishing.  • Protects surfaces from moisture penetration. • Protects surfaces from rust/uv rays. ANY TWO OF THE ABOVE (2) Copyright reserved Please turn over
Downloaded from hlayiso.com Civil Technology: Woodworking 3 DBE/November 2018 NSC – Marking Guidelines 1.5 The curing of concrete: • Increases the strength of concrete.  • Decreases the permeability of hardened concrete. • Improves durability of concrete by reducing cracks. • Makes concrete more watertight. • Minimises shrinkage cracks in concrete. • Provides volume stability. • Cured concrete can carry more weight without breaking/crumbling than uncured concrete. • Prevents rapid drying of concrete. • Curing ensures that the hydration process continues. ANY ONE OF THE ABOVE (1) 1.6 1.6.1 Multi detector  (1) 1.6.2 Tool A is used: • to detect materials found in/behind walls, ceilings and underneath floors, including ferrous and non-ferrous metals, electrical wiring, wood and metal studs.  • to locate steel bars and copper pipes.  • in carpentry, plumbing, and construction. • to measure the distance to/from covered objects. ANY TWO OF THE ABOVE (2) 1.6.3 The batteries must be removed from the tool: • to prevent the battery from running flat/battery can die.  • to prevent acid leaks from batteries damaging the tool. ANY ONE OF THE ABOVE (1) 1.7 1.7.1 A – Bolt and nut/Bolt  B – Rawl bolt  (2) 1.7.2 Bolt and nut • Bolts and nuts are used to secure pipe supports to metal parts.  • To join components together. Rawl bolt • A Rawl bolt is used to fix a truss hanger to a wall.  • To fix brackets/structures/panels to a wall/concrete. • For construction, renovation and industrial work ANY TWO OF THE ABOVE (2) [20] Copyright reserved Please turn over
Downloaded from hlayiso.com Civil Technology: Woodworking 4 DBE/November 2018 NSC – Marking Guidelines QUESTION 2: GRAPHICS AS METHOD OF COMMUNICATION (GENERIC) ANSWER SHEET 2 NO. QUESTIONS ANSWERS MARKS 1 Identify FIGURE A. South Elevation/Elevation  1 2 Identify FIGURE B. Ground floor plan/Floorplan  1 First floor level/Second floor 3 Identify number 4. level/Suspended floor/Floor level/ 1 Dash line/ FFL/Expansion joint  4 Identify number 5. Window Sill  1 Hand wash basin/Wash 5 Identify number 9. 1 basin/Washing basin/HWB/Basin  6 Identify number 10. Water closet/WC/Toilet pan  1 7 Identify number 11. Bath/B  1 8 On what date was the plan printed? 2018/10/02  1 9 Who drew the building plan? JP Maloi  1 Name the feature in the column for the 10 notes in FIGURE 2 that must be Ramp  1 installed in front of the sliding door. Name the feature in the column for the 11 notes in FIGURE 2 that must give Staircase/Stairs/Stairway 1 access to the first floor. Identify the type of roof that is used for 12 Gable roof  1 the building in FIGURE A. To cover the opening/close the gap between the two slopes of the roof.  13 Explain the purpose of number 1. Prevent water and other elements 1 from entering the roof. ANY ONE OF THE ABOVE Copyright reserved Please turn over
Downloaded from hlayiso.com Civil Technology: Woodworking 5 DBE/November 2018 NSC – Marking Guidelines • To prevent water from falling onto the ground  • To collect rainwater • To channel the rainwater into the downpipe 14 Explain the purpose of number 2. • To protect the wall from water 1 • To hide the rafters/finish off the roof ANY ONE OF THE ABOVE Explain the abbreviation FFL at 15 Finished floor level  1 number 6. To channel the water from the gutter 16 Explain the purpose of number 7. 1 to the ground.  Explain the meaning of the arrow on It indicates the direction of the slope 17 the feature that must be installed in 1 of the ramp/it indicates the slope.  front of the sliding door. It indicates the slope or the gradient Explain what is meant by 1:10 of the ramp/for every 10 metres 18 1 indicated on the symbol in the notes. horizontally rises 1 metre vertically. 19 Which room will feature 15 serve? The bathroom.  1 • Indicates what direction the window is opening/window opening.  Explain the short dash lines on the • Indicates the location of the 20 hinges. 1 windows. • Indicates the location of the casement stay. ANY ONE OF THE ABOVE Deduce the height of window 2 from 21 1,2 m or 1 200 mm (Ignore units) 1 the window schedule. Deduce the width of window 3 from 22 2 m or 2 000 mm (Ignore units) 1 the window schedule. On what elevation of the building is 23 Western elevation/Western side  1 the bathroom window situated? Copyright reserved Please turn over
Downloaded from hlayiso.com Civil Technology: Woodworking 6 DBE/November 2018 NSC – Marking Guidelines 3 – window/window frame/reveal Differentiate between component frame stile/casement stile  24 2 number 3 and component number 8. 8 – sliding door /door frame/ door/reveal /sliding door stile  The light in the lounge is a fluorescent light/1 x 40W-/2x40- Differentiate between the light in the 25 /3x40 fluorescent light  and the 2 lounge and the light in the bathroom. light in the bathroom is a normal ceiling light  Tile/ Vinyl flooring(Novilon)/ Coloured screed/Polished or stained Recommend a suitable floor covering concrete flooring/Water proof 26 1 for the bathroom. laminated floor/carpet.  ANY ACCEPTABLE ANSWER Recommend an appropriate scale to 27 which FIGURE A should be drawn, 1:50/100/200  1 according to SANS. Recommend an alternative sanitary 28 fitment to replace number 11 that will Shower  1 serve a similar purpose. Calculate the internal area of the office 4 m  x 3 m  = 12 m²  OR 12 29 3 in m² Show ALL calculations. 4 000 X 3 000 = 12 000 000mm2 Positive marking (220 + 3 000 + 110 + 2 800 + 220)  x 2  = 6 350 x 2 =12 700 mm  Calculate the perimeter of the building. (220 + 4 000 + 110 + 2 000 + 220)  x 2  30 = 6 550 x 2 7 Show ALL calculations. = 13 100 mm  12 700 + 13 100 mm = 25 800 mm  OR = 25,8 m TOTAL 40 Copyright reserved Please turn over
Downloaded from hlayiso.com Civil Technology: Woodworking 7 DBE/November 2018 NSC – Marking Guidelines QUESTION 3: CASEMENTS, CUPBOARDS, WALL-PANELLING AND QUANTITIES (SPECIFIC) 3.1 3.1.1 Tongue and groove boards  (1) 3.1.2 520 mm - 570 mm  (1) 3.1.3 Cornice  (1) 3.1.4 Drip groove  (1) 3.1.5 Fanlight  (1) 3.2 3.2.1 • A – Wood/Timber  (1) • B – Glass/Perspex  (1) 3.2.2 This part is holding the glass/pane in its place.  (1) 3.3 3.3.1 • A Storage space/top unit  • B Hanging space  • C Shelves/storage space/shelf  • D Drawers  (4) 3.3.2 Melamine: • is waterproof.  • is easier to clean. • is more durable. • enhance inside appearance. • has a smooth finish. OR Chipboard: • Is not water proof • Is not easy to clean • Is less durable • Does not enhance the inner appearance • Is not as smooth (1) ANY ONE OF THE ABOVE 3.3.3 • E – Front rail/Top rail  • F – Oval hanging rail/Hanging rail/Pipe rail  • G – Side  • H – Kick plate/base/Bottom rail/Plinth  (4) Copyright reserved Please turn over
Downloaded from hlayiso.com Civil Technology: Woodworking 8 DBE/November 2018 NSC – Marking Guidelines 3.4 3.4.1 • A – Cornice  • B – Horizontal rough grounds  • C – Quarter round/Quadrant  (3) 3.4.2 • To enhance appearance.  • To give an aesthetic appearance.  • There is no need to plaster the wall where panelling is to be done. • It serves as insulation against sound and heat. • For durability ANY TWO OF THE ABOVE (2) Copyright reserved Please turn over
Downloaded from hlayiso.com Civil Technology: Woodworking 9 DBE/November 2018 NSC – Marking Guidelines 3.5 A B C D 3.5.1 Internal measurements of long walls: = 9 000 – 2/220 = 8 560 mm  OR = 9 000 - 440 = 8 560 mm Length of wall plates needed: 2/ 8,56  17,12  17,12 m wall plate needed 3.5.2 (4) Number of purlins needed Number of purlins = Length of rafter +1 Distance between centres = 3,6  + 1 OR 3 600 + 1 0,9 900 = (4 + 1) 2 OR (5x2) = 10 purlins  (4) [30] Copyright reserved Please turn over
Downloaded from hlayiso.com Civil Technology: Woodworking 10 DBE/November 2018 NSC – Marking Guidelines QUESTION 4: ROOFS, CEILINGS, TOOLS AND EQUIPMENT, AND MATERIALS (SPECIFIC) 4.1 4.1.1 C (1) 4.1.2 A (1) 4.1.3 D (1) 4.1.4 E (1) 4.1.5 F (1) 4.2 4.2.1 • A Hipped end  • B Purlin  • C Ridge/Ridge plate  • D Valley rafter/Valley  • E Overhang/Eaves overhang  • F Gable end/Gable wall/Wall/Side of building  (6) 4.2.2 76 mm x 50 mm  76 mm x 76 mm ANY ONE OF THE ABOVE (1) 4.3 • It allows rain water to be directed into the gutter.  • So that water does not damage the end of the rafters. (1) ANY TWO OF THE ABOVE 4.4 • A good roof covering must be able to resist weather conditions such as rain and wind/resistance against corrosion.  • Should look durable and enhances the appearance of the building.  • Should be fire resistant. • Should provide insulation against heat and cold. ANY TWO OF THE ABOVE (2) Copyright reserved Please turn over
Downloaded from hlayiso.com Civil Technology: Woodworking 11 DBE/November 2018 NSC – Marking Guidelines 4.5   IBR sheeting  Corrugated iron sheeting  (4) 4.6 • The installation of steel roofing is faster.  • The installation of steel roofing is more economical.  • The installation of steel roofing is simpler. • Steel roof covering is cheaper than tiles. • Steel roof covering is environment friendly. ANY TWO OF THE ABOVE (2) 4.7 • If roof underlay is not installed there will be more dust inside the roof space.  • If roof underlay is not installed, the roof may not be fully waterproof.  • The risk of wind lifting tiles becomes greater. • Insulating would not be good. ANY TWO OF THE ABOVE (2) 4.8 • A - Tie beam  • B - Brandering  • C - Trapdoor  • D - Cover strip  (4) 4.9.1 • A – Router  • B – Combination belt and disc sander.  (2) 4.9.2 Store in a safe, dry place.  Store it in a wooden or plastic box away from moisture.  (2) 4.9.3 • Maintain like all machinery – lubricate and adjust according to the manufacturer’s instructions.  • Clean the belt/disc sander after use.  • Repair or replace damaged electrical cords. • Handle the sander so as not to damage or impair its accuracy. • Use machinery only for the intended purpose. • Do not force material onto the belt/disc of the sander. • Avoid the use of worn out (clogged) belts and discs. • Service the machine regularly. ANY TWO OF THE ABOVE (2) Copyright reserved Please turn over
Downloaded from hlayiso.com Civil Technology: Woodworking 12 DBE/November 2018 NSC – Marking Guidelines 4.9.4 • Table saw/Circular saw/Mitre saw  • Band saw  • Radial arm saw  • Jigsaw • Scroll saw ANY THREE OF THE ABOVE (3) 4.10.1 M – Mechanical grading  V – Visual grading  (2) 4.10.2 6 - The number indicates the strength.  (1) 4.10.3 The SABS symbol.  (1) [40] Copyright reserved Please turn over
Downloaded from hlayiso.com Civil Technology: Woodworking 13 DBE/November 2018 NSC – Marking Guidelines QUESTION 5: CENTERING, FORMWORK, SHORING AND GRAPHICS AS MEANS OF COMMUNICATION (SPECIFIC) 5.1 A - Concrete beam/Concrete  B - Brace/Strut  C - Prop/Adjustable prop  D - Sole plate  (4) 5.2 • Block board  • Laminated board  • Shutter board  • Plywood  • Timber • Hard board/Masonite ANY FOUR OF THE ABOVE (4) 5.3 • Wedges are inserted under the bearers and props to support the formwork.  • Wedges keep the different formwork components sturdy and fixed.  • Wedges help with the lowering and raising of the formwork.  • Wedges are used for the levelling of the formwork. • Wedges ease the striking of formwork. ANY THREE OF THE ABOVE (3) 5.4 • It supports more weight.  • Support the weight of the fresh concrete. ANY ONE OF THE ABOVE (1) 5.5 5.5.1 • A – Laggings  • B – Ribs  • C – Bearer  (3) 5.5.2 Brick arches because they have a solid surface.  (1) 5.5.3 Openly spaced laggings/Open laggings/Open  Laggings are not close to each other. (1) There are spacing’s between the openings of the laggings. ANY ONE OF THE ABOVE 5.6 5.6.1 • Dead shores are used to support structures.  • Dead shores carry dead weight above the dead shores, e.g. walls, floors. • Support existent walls if openings are made. • Transfer the weight of the structure to firm ground during structural renovations. • Support a wall if alterations are made. ANY ONE OF THE ABOVE (1) Copyright reserved Please turn over
Downloaded from hlayiso.com Civil Technology: Woodworking 14 DBE/November 2018 NSC – Marking Guidelines 5.6.2 Double flying shores provide temporary support to TWO parallel walls where one or two walls show signs of failure.  Double flying shores give temporary support to TWO parallel defective walls. Double flying shores can only be used with TWO parallel defective walls between 9 and 15 meters. ANY ONE OF THE ABOVE (1) 5.7 5.7.1 The steel dog is used to secure the joint between prop and needle.  (1) 5.7.2 Props are used to strengthen or brace the floors and ceiling.  (1) 5.7.3 Sole plates spread the weight transferred by the props over a wider area. Prevent vertical props/pipes from sinking into the ground. The soleplate create a level area where the props rest on. (1) 5.8 45°  (1) 5.9    Slope of roof 45°     Span/3 000 mm ASSESSMENT CRITERIA MARK CANDIDATE'S MARK Span 1 Wall plates 2 Rafters 2 Ridge beam 1 Slope of the roof 45° 1 TOTAL: 7 (7) [30] Copyright reserved Please turn over
Downloaded from hlayiso.com Civil Technology: Woodworking 15 DBE/November 2018 NSC – Marking Guidelines QUESTION 6: SUSPENDED FLOORS, STAIRCASES, IRONMONGERY, DOORS AND JOINING (SPECIFIC) 6.1 6.1.1 D (1) 6.1.2 C (1) 6.1.3 B (1) 6.1.4 A (1) 6.1.5 A (1) 6.2   Joist built into wall ASSESSMENT MARK CANDIDATE'S CRITERIA MARK Joist 1 Built into wall 1 TOTAL 2   Joist secured to wall with truss/joist hanger ASSESSMENT MARK CANDIDATE'S CRITERIA MARK Joist 1 Truss/Joist hanger 1 TOTAL: 2 (4) Copyright reserved Please turn over
Downloaded from hlayiso.com Civil Technology: Woodworking 16 DBE/November 2018 NSC – Marking Guidelines 6.3 Alternative drawing will also be acceptable        OR     (   ASSESSMENT MARK CANDIDATE'S CRITERIA MARK ONE one-brick pier 1 DPC/Proportion 1 Ant guard 1 Bearer 1 Joist 1 Floor boards 1 TOTAL 6 (6) Copyright reserved Please turn over
Downloaded from hlayiso.com Civil Technology: Woodworking 17 DBE/November 2018 NSC – Marking Guidelines 6.4 HAND RAIL NEWEL/NEWEL POST  LANDING  RISE   (5) TREAD 2 OR 3 DIMENSIONAL DRAWINGS WILL BE ACCEPTED 6.5 • Serves as a place of rest.  • For safety in case of a falling accident. • Facilitates a change in direction when moving up or down stairs. ANY ONE OF THE ABOVE (1) 6.6 6.6.1 Door stile/Lock rail  (1) 6.6.2 Frame stile/Door frame/Stile  (1) 6.6.3 Frame stile/Door frame/Stile  (1) 6.6.4 Door stile  (1) Copyright reserved Please turn over
Downloaded from hlayiso.com Civil Technology: Woodworking 18 DBE/November 2018 NSC – Marking Guidelines 6.7    OR ASSESSMENT MARK CANDIDATE'S CRITERIA MARK Raised panel top view 2 Raised and fielded panel 2 top view TOTAL 4 (4) 6.8 The opening allows shrinkage  and expansion of the panel/wood. (1) 6.9 A – Brace/Strut  B – Tongue and groove battens/V- Tongue and groove battens  C – Stile  (3) Copyright reserved Please turn over
Downloaded from hlayiso.com Civil Technology: Woodworking 19 DBE/November 2018 NSC – Marking Guidelines 6.10 6.10.1 Hinge (Any hinge accepted)  (1) 6.10.2 Clout nail/Chipboard screws/Drywall screw  (1) 6.10.3 Nail/Skew nail/Perm fix nail  (1) 6.10.4 Gang nail/Bolt and nut/Nails  (1) 6.11 • Hinges  • Casement fasteners  • Casement stays ANY TWO OF THE ABOVE (2) [40] TOTAL: 200 Copyright reserved

Study this subject

More from Grade 12 Civil Technology

View all